Kategori Produk
Produk
Kupon
Trend
Caranya
x
14 produk ditemukan
Kunjungi Toko
Arduino MAX7219 Dot Matrix MCU LED Display Control Module Kit For With Dupont Cable
Rp 66.000
Banggood

Max7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the Cpu, the output port connect to the input port of the second one, and so on. In the case of 51 Mcu: VCC →; 5V GND →; GND DIN →; P22 CS →; P21 CLK →; P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4.Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 1 x LED module 5 x Dupont line (20cm)

Selengkapnya
Kunjungi Toko
Arduino Printer MKS Mega 2560 Module Ramps 1.4 DIY Controller 24V for Arduino R3 Board with USB Cable
Rp 322.000
Tomtop

Features: Fully compatible with Arduino 2560-r3. USB to serial 16 U2, flexible; can achieve high speed transmission and equipment renaming by modifying firmware; and the device can be re-named. 7-25V wide input voltage. Compared with most products on the market (frequently burned and easily fever even at 12V), no longer use a separate 1117 LDO for power supply, provides much higher stability. 3D printers' perfect partner.

Selengkapnya
Kunjungi Toko
−33%
Arduino 5 Pcs LANDAI Switch Mekanik Endstop 1.4 With Kabel For 3 D Printer Makerbot Prusa Mendel Rep Rap CNC Arduino Mega 2560 1280
Rp 61.000 Rp 92.000
Lazada
Kunjungi Toko
−15%
Arduino ARDUINO MEGA 2560 R3 + KABEL USB(REX-MART)
Rp 295.000 Rp 350.000
Lazada
Kunjungi Toko
Arduino 5 Pcs LANDAI 1.4 Mekanik Endstop Switch dengan Kabel untuk 3D Printer Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 1280-Intl
Rp 95.000
Lazada
Kunjungi Toko
−28%
Arduino 70cm 4 Pin Female to Female Jumper Wire 4P Dupont Cable for arduino 3D Printer - intl
Rp 40.000 Rp 56.000
Lazada
Kunjungi Toko
−29%
Arduino LDTR - YJ028 / C 4 - Pin Female to Female Wire Jumper Cable for Arduino / 3D Printer - intl
Rp 68.000 Rp 97.000
Lazada
Kunjungi Toko
−55%
Arduino CNC Shield V4 Expansion Board 3PCS A4988 Nano USB Cable For Arduino 3D Printer - intl
Rp 205.000 Rp 454.000
Lazada
Kunjungi Toko
−28%
Arduino 10pcs cnc shield v3 engraving machine 3D Printer+ 4pcs A4988 driver expansion board for Arduino + UNO R3 with USB cable - intl
Rp 1.658.000 Rp 2.322.000
Lazada
Kunjungi Toko
−28%
Arduino 3pcs cnc shield v3 engraving machine 3D Printer+ 4pcs A4988 driver expansion board for Arduino + UNO R3 with USB cable - intl
Rp 512.000 Rp 717.000
Lazada
Kunjungi Toko
Arduino Uno R3 Development Board dengan Kabel
Rp 145.000
Lazada
Kunjungi Toko
Arduino 5pcs 100cm 3D Printer Male to Female Male + Female 2 Pin Wire Dupont Cable For Arduino Breadboard
Rp 42.000
Newfrog

5pcs 100cm 3D Printer Male to Female Male + Female 2 Pin Wire Dupont Cable For Arduino Breadboard

Selengkapnya
Kunjungi Toko
Arduino High Quality Smooth Control Control Board+ Data Cable for 3D Printer MKS GEN V1.4 RAMPS 1.4 Arduino 2560 Board DRV8825 Hot Sale
Rp 449.000
Newfrog

High Quality Smooth Control Control Board+ Data Cable for 3D Printer MKS GEN V1.4 Ramps 1.4 Arduino 2560 Board Drv8825 Hot Sale

Selengkapnya
Kunjungi Toko
Arduino 2004 LCD Smart Display Screen Controller Module with Cable for RAMPS 1.4 Arduino Mega Pololu Shield Arduino Reprap 3D Printer Kit
Rp 125.000
Tomtop

Features: 2004 LCD smart controller for 3D printer. Supports for Ramps 1.4 control board. Built-in encoding function allows you adjusting the parameter and selecting file to print. 3in screen, clear white characters with blue backlit, displays 4 lines and 20 characters per line. With 5 buttons to enter Menu and axis direction adjustment.

Selengkapnya